Name: Industrial Metal Cutting Disc 115 x 1.0 x 22.2mm
Brand: TORK CRAFT
SKU: ABR115S-10
Price: 7.92 ZAR
Availability: InStock

Industrial Metal Cutting Disc 115 x 1.0 x 22.2mm

Stock: 1 - 5 Days
Cat No: ABR115S-10 652
SKU: ABR115S-10
UPC: 6009515860448

TORK CRAFT

Product Views: 827

Based on 0 reviews. - Write a review

Don't snooze, this offer ends in:

Day

Hour

Min

Sec

R 7.92

R 11.00

Qty

Add to Cart

Buy Now Ask Question

Add to Wish List Compare this Product

Tork Craft Industrial Metal & Stainless Steel Cutting Disc 115 x 1.0 x 22.2 mm

At a Glance: Industrial cutting disc for steel and stainless steel, featuring a slim 1.0 mm profile, 115 mm diameter, fibreglass mesh reinforcement and maximum operating speed of 13,300 rpm.

Get your metalwork ready for assembly with the Tork Craft ABR115S-10 Industrial Metal & Stainless Steel Cutting Disc. Designed for use on a compatible 115 mm angle grinder, this abrasive disc is suitable for cutting steel and stainless steel components during fabrication, fitting and repair work. Its slim 1.0 mm profile creates a narrower cutting path than thicker discs, helping reduce the amount of material removed along the cut. Fibreglass mesh reinforces the wheel, while the compact diameter suits cutting sheet, tubing, flat bar and profiles within the grinder&s capacity. Whether you are trimming a bracket, preparing tubing or cutting a replacement component to length, use secure workpiece support, the correct cutting guard and a steady feed to guide the disc through the material.

Industrial cutting disc with a Slimline profile

The disc carries both Industrial and Slimline markings. Its nominal 1.0 mm thickness provides a thin cutting profile, with a supplier-stated thickness tolerance of ±0.2 mm. Use the disc&s edge for cutting and keep it aligned with the cut. Select a separate suitable accessory for grinding or finishing.

Product highlights

Industrial range: Identified as a Tork Craft Industrial cutting disc.
Steel and stainless steel: Suitable for common fabrication and workshop cutting tasks involving these materials.
Slim 1.0 mm profile: Produces a narrower cutting path than thicker cutting discs.
115 mm diameter: Fits compatible 115 mm angle grinders with the correct mounting arrangement.
Fibreglass mesh reinforcement: Reinforces the abrasive wheel.
13,300 rpm maximum speed: Clearly defined operating limit for matching the disc to the grinder.

Compatibility

Angle grinders: Suitable for 115 mm angle grinders approved for this disc diameter, thickness and mounting bore.
Mounting bore: Listed as 22.2 mm in the product title and on the disc label; the detailed supplier specifications state 22.22 mm, nominally 7/8 inch.
Workpiece materials: Steel and stainless steel sheet, tubing, flat bar, angle and other suitable sections within the grinder&s cutting capacity.
Guard and flanges: Requires an appropriate cutting guard and the mounting flanges specified by the grinder manufacturer.
Speed rating: The grinder&s maximum rated speed must not exceed the disc&s 13,300 rpm limit.

Features

Industrial designation: Part of the Tork Craft Industrial cutting disc range.
Slimline profile: Nominal 1.0 mm thickness with a stated tolerance of ±0.2 mm.
115 mm diameter: Sized for compatible compact angle grinders.
Fibreglass mesh reinforcement: Reinforced abrasive wheel construction.
Steel and stainless steel application: Suitable for cutting components made from these materials.
Marked speed limit: Maximum operating speed of 13,300 rpm.

Benefits

Narrow cutting path: The thin profile removes less material along the cut than thicker discs when correctly guided.
Prepare parts for assembly: Cut suitable tubing, bars and profiles to the required length.
Useful across workshop tasks: Supports fabrication, installation and repair work involving steel and stainless steel.
Plan finished dimensions: The stated thickness helps you allow for material removed when positioning the cut.

Application

Cutting steel and stainless steel sheet or panels to size.
Cutting suitable tubing and hollow sections to length.
Trimming steel and stainless steel flat bar, angle and profiles.
Preparing brackets and components for fabrication.
Cutting suitable steel threaded rod and fasteners to length.
Trimming replacement components during fitting and repair work.

Extra Information

Product weight: 200 g.
Thickness tolerance: The nominal disc thickness is 1.0 mm, with a supplier-stated tolerance of ±0.2 mm.
Bore measurement: The 22.2 mm listing and 22.22 mm detailed specification describe the nominal 7/8 inch mounting size. Confirm compatibility with your grinder&s mounting system.
Cut allowance: Allow for the material removed by the disc when marking a component&s finished length.
Stainless steel cleanliness: Reserve a disc for stainless steel work and keep it separate from accessories used on mild steel to reduce contamination.
Disc wear: The diameter decreases during use, reducing the available cutting depth.
Storage: Keep discs dry and protected from impact, moisture and excessive heat. Observe any expiry date marked on the disc.

Cutting only: Use the disc&s edge for cutting. Do not grind with its side face or twist it inside the cut.

Pro Tips

Mark the finished length carefully and cut on the waste side of the line, allowing for the cutting width.
Clamp the workpiece securely and arrange supports so the cut cannot close and pinch the disc.
Keep the grinder aligned with the cut. Stop the disc before repositioning the tool.
Use steady, moderate pressure. Forcing a thin disc can cause deflection and increase the risk of damage.
For stainless steel projects, use a dedicated disc and keep the work area free of mild steel debris.
Allow the cut piece to cool, then remove burrs with a suitable finishing accessory.

How to Use

Confirm that the workpiece is suitable steel or stainless steel and that the grinder accepts the disc&s 115 mm diameter, thickness and mounting bore. Check that the grinder&s maximum rated speed does not exceed 13,300 rpm.
Switch off the grinder and disconnect its power supply or remove the battery before fitting the disc.
Inspect the disc for damage and check its expiry marking. Fit an undamaged, in-date disc using the flange arrangement and tightening method specified in the grinder manual.
Fit the appropriate cutting guard and auxiliary handle. Confirm that the disc is secure and rotates freely without touching the guard.
Mark and clamp the workpiece, allowing for the cutting width. Support the material to prevent pinching and clear the spark path of people and combustible materials.
Wear the required protective equipment, hold the grinder with both hands and briefly run the disc clear of the workpiece. Stop immediately if abnormal vibration occurs.
Allow the grinder to reach operating speed before entering the cut. Guide the disc straight through the material with steady pressure, avoiding twisting and sideways loading.
At the end of the cut, withdraw the disc, switch off and wait for it to stop completely before putting the grinder down. Disconnect the power before changing accessories.

Safety

Wear safety glasses, a face shield, hearing protection and suitable respiratory protection for the cutting task.
Wear suitable gloves, protective clothing and safety footwear. Keep loose clothing, jewellery and hair clear of moving parts.
Use the correct cutting guard and auxiliary handle, and hold the grinder securely with both hands.
Never exceed the disc&s maximum speed of 13,300 rpm. Check the markings on the actual disc before use.
Do not use cracked, chipped, distorted, damaged or expired discs. Never enlarge the bore or force the disc onto an unsuitable mounting system.
Cut with the disc&s edge only. Avoid sideways pressure, twisting and forcing the disc through the material.
Clamp and support the workpiece securely. Keep hands away from the cutting path and position your body clear of the disc&s plane of rotation.
If the disc binds, switch off and hold the grinder still until rotation stops. Correct the cause before restarting; never restart with the disc trapped in the cut.
Direct sparks away from people and combustible materials. Keep bystanders clear and maintain a tidy work area.
Do not introduce water or coolant unless both the grinder and disc are explicitly approved for that method.
Allow freshly cut pieces to cool before handling and take care around sharp edges.
Wait for the disc to stop completely before putting the grinder down. Disconnect the power before changing discs, making adjustments or leaving the tool unattended.

Specifications

Description	Spec
Brand	Tork Craft
Cat No.	ABR115S-10
Product Type	Abrasive cutting disc for steel and stainless steel
Barcode	6009515860448
Range	Industrial
Profile Marking	Slimline
Disc Diameter	115 mm
Nominal Disc Thickness	1.0 mm
Thickness Tolerance	±0.2 mm
Mounting Bore	22.22 mm in supplier specifications; listed and labelled as 22.2 mm, nominal 7/8 inch
Reinforcement	Fibreglass mesh
Maximum Operating Speed	13,300 rpm
Suitable Materials	Steel and stainless steel
Compatible Tool	Suitable 115 mm angle grinder
Intended Operation	Cutting only

In the Box / Packaging

1 x Tork Craft ABR115S-10 Industrial Metal & Stainless Steel Cutting Disc, 115 x 1.0 x 22.2 mm, per unit ordered.

Supplier pack size: 100 discs. The pack size indicates the supplier ordering quantity and packaging count; it does not mean that one unit contains 100 discs.

Tags: Cutting disc , Industrial Cutting Disc , Metal Cutting Disc , Steel Cutting Disc , Stainless Steel Cutting Disc , Slimline Cutting Disc , 115mm Cutting Disc , 1.0mm Cutting Disc , Metal Fabrication , Angle Grinder Accessories