Name: Masonry Cutting Disc 115 x 2.0 x 22.22mm
Brand: TORK CRAFT
SKU: ABR115M-5
Price: 14.40 ZAR
Availability: InStock

Masonry Cutting Disc 115 x 2.0 x 22.22mm

Great Value

Masonry Cutting Disc 115 x 2.0 x 22.22mm

Stock: 1 - 5 Days
Cat No: ABR115M-5 650
SKU: ABR115M-5
UPC: 6009675089529

TORK CRAFT

Product Views: 764

Based on 0 reviews. - Write a review

Don't snooze, this offer ends in:

Day

Hour

Min

Sec

R 14.40

R 20.00

Qty

Add to Cart

Buy Now Ask Question

Add to Wish List Compare this Product

Tork Craft Masonry Cutting Disc 115 x 2.0 x 22.22 mm

At a Glance: 115 mm masonry cutting disc with a 2.0 mm thickness and resin-bonded silicon carbide abrasive for cutting brick, concrete and stone.

Take on masonry cutting projects with the Tork Craft ABR115M-5. Designed for compatible 115 mm angle grinders, this abrasive cutting disc combines silicon carbide grains with a resin bond to cut brick, concrete and stone. Its 2.0 mm cutting profile makes it a practical accessory for sizing bricks, trimming stone pieces and preparing masonry materials for building or renovation work. From fitting a brick into a repair to making a straight cut along a marked line, this disc gives your grinder a dedicated masonry cutting option. Use it with the correct cutting guard, suitable dust extraction and a steady feed, keeping the disc aligned with the cut throughout the operation.

Silicon carbide abrasive for masonry cutting

Silicon carbide is the abrasive used in this disc to cut masonry materials. The resin bond holds the abrasive grains together while the rotating disc edge removes material along the cut line. The ABR115M-5 is intended for cutting only; its side face must not be used for grinding or surface finishing.

Product highlights

Dedicated masonry disc: Designed for cutting brick, concrete and stone.
115 mm diameter: Suitable for compatible angle grinders approved for this disc size.
2.0 mm thickness: A clearly specified cutting profile for selecting the right disc for your application.
Resin-bonded silicon carbide: Combines a masonry abrasive with a resin bond.
Maximum speed of 13,300 rpm: Check the grinder&s rated maximum speed against the disc rating before use.

Compatibility

Angle grinders: Compatible with suitable 115 mm angle grinders that accept the disc&s bore, thickness and approved flange arrangement.
Mounting size: The supplier specifies a 22.23 mm bore, also listed in the product title as 22.22 mm. This is the nominal 7/8-inch mounting size.
Workpiece materials: Intended for masonry cutting, including brick, concrete and stone.
Cutting accessories: Use the grinder manufacturer&s approved cutting guard and a compatible dust extraction shroud where available.

Features

Silicon carbide abrasive: Selected for cutting masonry materials.
Resin bond: Holds the abrasive grains together within the disc.
115 x 2.0 mm disc: Compact diameter with a 2.0 mm cutting profile.
Nominal 7/8-inch bore: Supplier specification of 22.23 mm, listed as 22.22 mm in the product name.
Cutting-only design: Intended for straight cuts using the disc edge.

Benefits

Match the disc to the material: A dedicated masonry abrasive helps you select an appropriate accessory for brick, concrete and stone.
Prepare pieces to fit: Useful for cutting masonry materials to suit planned dimensions and openings.
Practical for renovation work: Adds masonry cutting capability to a compatible 115 mm angle grinder.
Clear selection details: Published dimensions and speed markings help you check compatibility before fitting the disc.

Application

Cutting bricks to size for building and repair work.
Making straight cuts in concrete within the grinder&s permitted cutting capacity.
Cutting stone pieces for fitting and renovation tasks.
Making cuts for masonry wall chasing where the grinder, guard and dust extraction arrangement are approved for the operation.

Extra Information

Bore measurement: The product title states 22.22 mm, while the supplier specifications and disc label state 22.23 mm. Both describe the nominal 7/8-inch mounting size; confirm the correct fit with your grinder&s mounting flanges.
Abrasive cutting action: The disc removes material through abrasion and gradually wears down during use.
Cutting capacity: Available cutting depth depends on the grinder, guard, flange arrangement and remaining disc diameter.
Dust control: Cutting brick, concrete and stone can release respirable crystalline silica. Use suitable extraction and appropriate respiratory protection.
Storage: Keep discs dry and protected from impact, moisture and excessive heat. Observe any expiry date marked on the disc.

Important: This disc is designed for masonry cutting only. Do not use its side face for grinding, and do not twist it in the cut.

Pro Tips

Allow for the cut width: Mark the finished dimension clearly and position the cut on the waste side of the line.
Establish the cutting line: Begin with a controlled shallow pass before increasing depth, keeping the disc aligned throughout.
Support the material: Secure the workpiece so it cannot move or close onto the disc as the cut progresses.
Let the abrasive work: Apply steady, moderate feed pressure. Forcing the grinder increases the risk of binding and disc damage.
Control dust during cleanup: Use a suitable dust extractor for fine masonry dust. Avoid dry sweeping or blowing dust into the air.

How to Use

Check suitability: Confirm that the material, disc diameter, bore and thickness suit the grinder. The grinder&s rated maximum speed must not exceed the disc&s 13,300 rpm rating.
Disconnect the power: Switch off and unplug the grinder, or remove its battery, before fitting the disc.
Inspect and mount: Reject cracked, chipped, damaged or expired discs. Fit the disc with the correct flanges and tighten it according to the grinder manufacturer&s instructions.
Prepare the grinder: Fit the approved cutting guard and auxiliary handle. Connect a compatible cutting shroud and suitable dust extractor where the equipment permits.
Prepare the work area: Mark the cut and secure the material with suitable support. Before cutting walls, check for concealed electrical cables and pipes.
Start safely: Wear appropriate protective equipment, hold the grinder with both hands and run it clear of the workpiece. Check for abnormal vibration before beginning the cut.
Make the cut: Allow the grinder to reach operating speed, then guide the disc along the marked line with steady pressure. Keep it straight and avoid twisting or sideways loading.
Finish safely: Withdraw the disc from the cut, switch off and wait until it has stopped completely before putting the grinder down. Disconnect the power before removing or replacing the disc.

Safety

Wear eye, ear and respiratory protection. Use safety glasses with a suitable face shield, hearing protection and respiratory protection appropriate for masonry and silica dust.
Use suitable dust extraction. Respiratory protection must fit correctly and form part of an effective dust control arrangement.
Wear suitable gloves, protective footwear and close-fitting clothing. Keep loose clothing, jewellery and hair away from rotating parts.
Keep the approved cutting guard and auxiliary handle fitted. Hold the grinder firmly with both hands.
Never exceed the disc&s 13,300 rpm maximum speed. Check the rating marked on the actual disc before use.
Inspect the disc before fitting it. Do not use a cracked, chipped, damaged or expired disc, and never alter its mounting hole.
Cut with the disc edge only. Do not side grind, bend, twist or force the disc through the material.
If the disc binds, switch off and hold the grinder still until rotation stops. Correct the cause before continuing, and do not restart with the disc trapped in the cut.
Check walls for concealed cables and pipes before cutting. Keep bystanders clear of debris and the dust exposure area.
Do not introduce water unless both the disc and grinder are specifically approved for wet cutting.
Wait for the disc to stop completely before placing the grinder down. Disconnect the power before accessory changes or adjustments.

Specifications

Description	Spec
Brand	Tork Craft
Cat No.	ABR115M-5
Product Type	Abrasive masonry cutting disc
Barcode	6009675089529
Disc Diameter	115 mm
Disc Thickness	2.0 mm
Bore Diameter	22.23 mm, nominal 7/8-inch bore; listed as 22.22 mm in the product title
Abrasive Material	Silicon carbide
Bond Type	Resin
Maximum Rotational Speed	13,300 rpm
Maximum Peripheral Speed	80 m/s
Suitable Materials	Brick, concrete and stone
Compatible Tool	Suitable 115 mm angle grinder
Intended Operation	Masonry cutting only

Packaging

Tork Craft ABR115M-5 Masonry Cutting Disc, 115 x 2.0 x 22.22 mm.
Supplier pack size: 10 discs.

Tags: Cutting masonry , 115mm dia cutting disc , Masonry Cutting Disc , 115mm Cutting Disc , 2.0mm Cutting Disc , Brick Cutting , Concrete Cutting , Stone Cutting , Silicon Carbide , Resin Bonded Disc , Angle Grinder Accessories

From Same Category

Cutting Disc Masonry 230 X 3.0 X 22.22mm

Great Value

Brand: TORK CRAFT

Cutting Disc Masonry 230 X 3.0 X 22.22mm

Cutting disc for masonry Compatible with 230mm dia. angle grinders. Manufactured from high quality Resin and Silicon Carbide. Designe..

R 43.20 R 60.00

Add to Cart

Add to Wish List Compare this Product

More Information

Cutting Disc Masonry 230 X 2.5 X 22.22mm

Great Value

Brand: TORK CRAFT

Cutting Disc Masonry 230 X 2.5 X 22.22mm

Compatible with 230mm dia. angle grinders. Manufactured from high quality Resin and Silicon Carbide. Designed for masonry cutting only. ..

R 36.72 R 51.00

Add to Cart

Add to Wish List Compare this Product

More Information

Great Value

Brand: TORK CRAFT

Masonry Cutting Disc 115 x 1.6 x 22.2mm

Tork Craft Masonry Cutting Disc 115 x 1.6 x 22.2 mm At a Glance: 115 mm masonry cutting disc with a 1.6 mm thickness and nominal 22.2 mm bore. Resi..

R 12.24 R 17.00

Add to Cart

Add to Wish List Compare this Product

More Information

5 + 1 Free Cutting Disc For Masonry 115 X 1.0 X 22.2mm

Brand: TORK CRAFT

5 + 1 Free Cutting Disc For Masonry 115 X 1.0 X 22.2mm

Cutting disc for masonry Compatible with 115mm dia. angle grinders. Manufactured from high quality Resin and Silicon Carbide. Des..

R 59.04 R 82.00

Add to Cart

Add to Wish List Compare this Product

More Information

Masonry Cutting Disc 115 x 2.5 x 22.22mm

Great Value

Brand: TORK CRAFT

Masonry Cutting Disc 115 x 2.5 x 22.22mm

Tork Craft Masonry Cutting Disc 115 x 2.5 x 22.22 mm At a Glance: 115 mm masonry cutting disc with a 2.5 mm thickness and resin-bonded silicon carbid..

R 14.40 R 20.00